Porous Ceramic Foam Filtration

24 de marzo Filtración mediante espuma cerámica porosa

Posted at 06:31h in Filtro de espuma cerámica by AdTech 0 Comments

0 Likes

Porous Ceramic Foam Filtration is used to produce high-quality aluminum plates, aluminum foils and other castings.
It can effectively remove the inclusions in the liquid aluminum through physical adsorption and chemical adsorption, thereby eliminating the defects of the casting, improving the quality of the casting, and providing excellent materials for further processing.
Porous Ceramic Foam Filtration can be used to remove oxides and other inclusions. Ceramic Foam Filtration is a white or milky white honeycomb ceramic filter.

Filtro de espuma cerámica «Dimension»
660 x 660 x 50 (26 pulgadas)
584 x 584 x 50 (23 pulgadas)
508 x 508 x 50 (20 pulgadas)
432 x 432 x 50 (17 pulgadas)
381 x 381 x 50 (15 pulgadas)
305 x 305 x 50 (12 pulgadas)
228 x 228 x 50 (9 pulgadas)
178 x 178 x 50 (7 pulgadas)

Filtro de espuma cerámica. Tamaño de poro (PPI): 10/20/30/40/50/60

The filter should be preheated before use, and the filter should be completely sealed in the filter box to ensure that all liquid aluminum flows through the filter, and the total amount after infiltration should not exceed the limit of the ceramic foam filter.
If there is too much slag in the liquid, more debris or reduce the total amount of percolation to adjust.

Correctly choose Porous Ceramic Foam Filtration to improve the cleanliness of aluminum melt
1. The selection of the ceramic foam filter board Se determina en primer lugar en función del contenido de impurezas en el aluminio fundido y del caudal de transferencia de la masa fundida, de acuerdo con los requisitos de calidad del producto fundido final.

There are many impurities and the quality of the cast products is average. A foam ceramic filter plate with larger mesh can be selected, and a glass cloth coarse filter is added in front of the filter plate. At this time, it is important to filter the semi-continuous casting with glass cloth first. It can intercept the slag that is scoured when the eye is opened and the slag washed down by the launder to prevent clogging of the filter plate.

The quality requirements of the casting products are high, and the new type of ceramic foam filter with small pore meshes, that is, large meshes, is selected to achieve the ideal cleanliness and obtain good results.

The selection of filter plate specifications is determined by the flow rate and total throughput of the melt. If the flow rate is large, the total throughput is large, and the filter plate has small holes, a larger size is used.

2. A la hora de elegir una placa filtrante, también debes fijarte en el color, hacer fotos y grabar los objetos.
The color is pure and free of impurities, which means that the material is uniform; if the hands are not sticky, it means that the surface is not sprayed with adhesive and will not cause secondary pollution.

Hold the filter plate with one hand, and clap the filter plate with the other hand, and continuously drop the ceramsite slag, indicating that the filter plate is inferior and will cause damage.
Into secondary pollution aluminum liquid.

Use an open flame or electric heating to heat up and burn to red and immediately cool at room temperature without cracking or slag, indicating that it is a good filter plate.

3. When purchasing filtration, carefully evaluate the effective specific surface area or porosity calculation of the foam. You can observe the uniform state of the mesh on the surface of the filter plate, and then open it to observe the uniform state of the mesh on the section.

Si es posible, la porosidad puede calcularse mediante el método de drenaje. La malla tridimensional es homogénea y la porosidad es relativamente elevada. Se trata de una excelente placa filtrante de cerámica celular.