مصنع Cff للألمنيوم

26 أغسطس مصنع Cff للألمنيوم

Aluminium Cff Factory produces aluminum casting ceramic foam filters that can remove metal slag, and the solution of metal impurities is much stronger than several other filter media, and combines physical and chemical principles to filter it.
The large impurities on the filter surface include physical barriers, interceptors and tiny impurities, which have chemical affinity and are attracted to the filter surface.
Therefore, impurities are effectively filtered out of cast products of various sizes, including pores that are much smaller than impurities.
Benteler Aluminium This Adtech الألومنيوم Cff can comb the entire chaotic molten metal flow, reduce turbulence, and make the molten metal.
The flow should be smooth and clean. Benteler Aluminium engineers are also thinking that other rate smelters recommend this filter plate

Aluminium Cff Factory Email: sales@adtechamm.com

تصنيف مرشحات الرغوة الخزفية المستخدمة في مصبوبات الألومنيوم
The alumina ceramic foam filter used as a molten aluminum filter for cast aluminum is used for pure filtration of molten aluminum.
The filtration efficiency of Aluminium Cff Factory is closely related to its correct installation and use. At the same time, due to the filtration process, the conventional and necessary measures taken to reduce the generation of inclusions in process operations such as smelting, furnace treatment and casting cannot be ignored. It is also necessary to prevent contamination of the filtered clean aluminum liquid again.

Benteler Aluminium introduces that its installation and use usually need to pay attention to the following aspects
1. Correct selection of the filter plate: it must be based on the flow range of the specific casting type, the maximum level of the metal during the filtration process, the total filtration volume, and the cleanliness of the original aluminum liquid.
2. Pre-melt filtration treatment can not be ignored: such as aluminum melting furnace, ordinary slag of holding furnace, cleaning furnace; refining in furnace. In particular, an online degassing device is still needed because it not only reduces the hydrogen content of the melt, but also removes some non-metallic inclusions.
3. The filter plate should fit the square refractory filter box: both need to be sealed to prevent metal from flowing into the casting box from the gap without being filtered, and to avoid the weight of the foam filter plate floating in the aluminum water. And failed. Aluminium Cff Factory Email: sales@adtechamm.com
4. التسخين المسبق قبل الاستخدام: قم بالتسخين المسبق لإزالة الرطوبة وتسهيل عملية الترشيح الأولية المؤقتة. يمكن استخدام التسخين الكهربائي أو التسخين بالغاز للتسخين المسبق. عادةً ما يستغرق ذلك حوالي 15 دقيقة.
5. في عملية الترشيح العادية، لا توجد حاجة إلى استخدام الخبث لتجنب حدوث صوت طرق أو اهتزاز في لوحة المرشح. وفي الوقت نفسه، يجب ملء خزان الغسل بالألمنيوم المنصهر لتجنب التداخل المفرط مع الألمنيوم المنصهر.
6. After casting, pour the metal into the flow cell and filter plate. There is a vibrator abroad, which is placed on the filter plate and shaken for one minute to shake off about 75% of the remaining liquid metal from the filter plate.
7. وأخيرًا، قم بتنظيف الأجزاء المحيطة وإزالة لوحة الترشيح بعد المعالجة.

مقالات ذات صلة:

مصنع مرشحات الرغوة الخزفية في الصين مصنع مرشحات مسبك السيراميك الموصى به من قبل شركة «دنمارك ألومنيوم» مصنع مرشحات الصب مصنع مرشحات الرغوة المعدنية مصنع مرشحات Cff المرشح الخزفي Cff Cff للمعدن المنصهر مصنع مرشحات الزركونيا الألومنيوم Cff مصنع «فيلتر فاوندري» مصنع مرشحات الألومينا الألمنيوم المنصهر Cff Alu Aluminium Cff مرشح Cff من Trimet Aluminium